DuraFlex Chimney Cap & Crown Nationwide

DuraFlex Chimney Cap & Crown in Easton: What to Know First

We provide independent DuraFlex chimney cap and crown service in Easton, with most jobs completed in a single visit and upfront pricing that matches the final invoice. A standard DuraFlex cap replacement or crown repair typically runs between $285 and $650 depending on flue count and access, and we carry the common DuraFlex stainless cap sizes on our trucks. This page is for homeowners who already know they’ve got DuraFlex components on their chimney and want a technician who won’t treat it like generic hardware. Call (610) 756-1504 - a live person answers, 24 hours a day.

Call (610) 756-1504

How DuraFlex Products Fail - and How We Fix Them

• DuraFlex SW 304/316 flexible liner caps - The mesh on these factory caps is 5/8-inch, which is fine for most fuel types but clogs faster in Easton’s oak-heavy burn zones than the 3/4-inch aftermarket equivalent we stock. We see collapsed mesh every February after a heavy burning season. Our fix: pull the cap, assess mesh integrity, and upgrade to a Gelco or Olympia Chimney 3/4-inch mesh cap if the homeowner burns hardwood four-plus months a year. Keeps the draft steady without voiding the liner warranty.
• DuraFlex DVL double-wall stovepipe termination caps - The stamped steel storm collar on DVL caps fatigues at the crimp after seven to ten winters of Easton’s freeze-thaw cycle. Water tracks down the pipe and rusts the inner wall. We replace with a fabricated stainless storm collar and reseal with Furno-Cast crown sealant, not silicone. Silicone looks fine in October and cracks by January.
• DuraFlex Pro 1.5-inch air-insulated chimney cap assemblies - The air gap in these caps traps moisture when the gasket between cap and base plate hardens. We’ve found this on three homes near the Bushkill Creek where humidity sits higher. Our fix: replace the gasket with a high-temp silicone-composite part and drill a weep hole if the original design didn’t include one. DuraFlex didn’t add factory weep holes until the 2019 production run.
• DuraFlex relined chimney crowns with poured concrete overhang - When a DuraFlex liner is retrofitted through an existing crown, the coring often fractures the crown edge. Water enters the crack, freezes, and spalls the concrete in sheets. We see this on Easton’s 1920s colonials near the Delaware Canal where the original crown was only two inches thick. Our fix: grind back to sound concrete, apply HeatShield CrownCoat in two passes, and reset the cap with a proper saddle slope so water runs off, not in.
• DuraFlex multi-flue cap installations on wide masonry chimneys - The stock DuraFlex multi-flue cap ships with universal legs that don’t always seat level on irregular Easton brickwork. Gaps under the legs channel water straight to the crown. We fabricate custom leg extensions from 304 stainless or switch to a Gelco multi-flue cap with adjustable pitch legs. Either way, we bed the legs in polyurethane sealant and torque to spec, not hand-tight.

Our DuraFlex Chimney Cap & Crown Process

1. 1
   Call and schedule. A live person answers, asks what you’re burning, how old the installation is, and whether you’ve noticed water or draft issues. We book a window and send a confirmation text.
2. 2
   Level-2 camera inspection on arrival. Our technician runs a camera up the flue to document liner condition, then photographs the cap, crown, and flashing from the roof. You see the photos on a tablet before we quote.
3. 3
   Parts decision. If your DuraFlex cap is under warranty and the failure is a factory defect, we note it for your records and install OEM. If the cap failed from age, weather, or fuel type, we quote OEM and quality aftermarket options with the trade-offs explained plain.
4. 4
   The repair. We replace or coat, reseal, and reflash per manufacturer spec. Crown repairs get a minimum 24-hour cure before cap reset. No shortcuts.
5. 5
   Post-repair test. Smoke test or draft gauge to confirm proper draw. Photos of the finished work. Written report with the 90-Day Done Right Promise attached.
6. 6
   Cleanup and walkthrough. We haul old material. You approve the work before we leave. The number on the estimate is the number on the invoice.

What DuraFlex Chimney Cap & Crown Costs in Easton

Steep roofs, slate surfaces, or chimneys over 35 feet add labor time. We quote everything upfront. Call (610) 756-1504 for a free estimate - we’ll look at your setup and give you a number that doesn’t change.

Why Easton Homeowners Call Hearthstone Chimney Co. for DuraFlex Work

We’ve been working on Easton chimneys since 1984. Russell Haines learned the trade hands-on through the building trades program at Los Angeles Trade-Technical College, then spent decades in the field before starting this company. That matters because DuraFlex caps and crowns aren’t theory - they’re physical parts that fail in predictable ways after specific numbers of winters, and you want someone who has seen those failures enough times to name them before the ladder goes up.

We document every inspection with photos and a plain-English verdict. Our 90-Day Done Right Promise is in writing with no arguing. If it’s not right, we come back. Our technicians are background-checked, uniformed, and carry DuraFlex, HeatShield, Gelco, and Olympia Chimney parts on the truck. Most jobs finish in one visit. And a live person answers the phone every hour of every day - because chimney problems don’t wait for business hours.

If the flue is clear and the mortar is sound, that’s all the good news you need.

FAQs